Modelithics — Literature

In this section you will find all available Application Notes, brochures, presentations, and published articles.
E-mail Modelithics Support If you have any questions about any of our literature


* X-parameters is a registered trademark of KeysightTechnologies.
Application Notes Release Notes Published Articles White Papers Brochures Presentations

Example files may require a Modelithics Library installation and license to use.
To request free trial click here.

55 Using Modelithics Models For Statistical Analysis In ANSYS HFSS Environment
Related file: CLR filter optimization and tolerance example in ANSYS
12/2/2015
 
54 Modelithics CLR Library In ANSYS HFSS
Related file: CLR example for ANSYS
12/2/2015
 
53 Analysis of a 65 W Power Amplifier Utilizing Modelithics’ Qorvo T2G4005528-FS Model In NI/AWR Software
Related file: NI/AWRDE Example for App Note 053
8/3/2015
 
52 A Design Flow For Rapid And Accurate Filter Prototyping
Related file: AWR Example for App Note052
6/29/2015
 
51 Axiem Co-simulation With Modelithics Models
Related file: AWR example for AN051
6/23/2015
 
50 Good, Better And Best: Techniques For Achieving First Pass Success In Lumped Element PCB -based Filter Designs
Related file: ADS example for AN50
Related file: ADS layout for AN50
3/18/2015
 
49 Analysis of a 30w Power Amplifier Utilizing Modelithics’ Triquint T2g6003028-FS Model
Related file: ADS example for AN49
7/1/2014
 
48 Recommendations For Port Setup When Using ADS Momentum And Modelithics Models4/3/2014
 
47 Behavioral Modeling of a Broadband Microwave Receiver12/18/2013
 
46 Improved Microwave Circuit Design Flow Through Passive Model Yield And Sensitivity Analysis
Related file: AWR example for AN46
11/2/2012
 
45 Simulation Procedures For Successful Low Noise Amplifier Design
Related file: ADS example for AN45
8/6/2012
 
44 Modelithics Substrate Library For Agilent’s Advanced Design System (ads) Adds Accuracy And Convenience To Board-based Designs
Related file: ADS example for AN44
8/10/2012
 
43 Modelithics Substrate Library For Genesys Adds Accuracy And Convenience To Board-based Designs
Related file: Genesys example for AN43
7/23/2012
 
42 Modelithics Substrate Library For AWR Microwave Office Adds Accuracy And Convenience To Board-based Designs
Related file: AWR example for AN42
6/6/2012
 
41 Frequency- And Time -domain Validation of a Non-linear Step Recovery Diode Model5/22/2012
 
40 Non-linear Reference Design Simulations
Related file: ADS example for AN40
4/19/2012
 
39 Accurate Co-simulation of Surface-mount Capacitors In Shunt Configurations3/15/2012
 
38 Design And Optimization of Lumped Element Couplers Using Modelithics Global Models10/17/2011
 
37 Performing EM-circuit Co-simulation With Modelithics Models Using Sonnet Suites9/23/2010
 
36 Effects of Over-molding On Surface Mount Capacitors And Inductors
 
35 Proximity Effects In Closely-spaced Surface Mount Passive Components
 
34 Model-based Design of a Varactor-tuned Filter: a Look At Layout Methods For Ensuring Simulation Accuracy1/15/2010
 
33 Understanding Noise Parameters Basics
 
32 Simulation Procedures And Considerations For Power Amplifier Design In Agilent Genesys
 
31 LDMOS Load-pull Simulation Using Agilent Genesys Software
Related file: Genesys example for AN31
 
30 Large-signal LDMOS Model Simulation Using Agilent Genesys Software
Related file: Genesys example for AN30
 
29 Lumped Element Low-pass Filter Design And Optimization Using Agilent Genesys Software
Related file: Genesys example for AN29
 
28 Accurate Non-linear Models Enable Successful Pin Limiter Design
( As Featured In RF Globalnet )
 
27 Pad Scaling Effects On Lumped Filters
 
26 Capacitor Pi Network For Impedance Matching
 
25 The Importance of Pad Geometry In Maximizing Surface Mount Component Mance (also Published Electronically By RF Globalnet)
 
23 Tolerance In Surface Mount Varactor Diodes
 
22 Part Value Tolerance In Surface Mount Components
 
21 Filter Design Using 0201 Surface Mount Lc's
 
20 Lumped Element Band-pass Filter Design And Optimization
 
19 Lumped Element High-pass Filter Design And Optimization
 
18 Lumped Element Low-pass Filter Design And Optimization
 
17 Lumped Element Filter Design And Optimization
 
15 Reducing Part Count In Low-pass Filter Designs
 
14 Capacitor Tee Network Characteristics
 
13 Effect of Mounting Orientation On Capacitor Response
 
12 Comparing Like Body-style Parts From Different Vendors
 
11 Substrate Effects On SMD Q-factor Behavior
 
10 Accounting For Substrate Thickness Tolerance In PCB Simulations
Related file: ADS Example Workspace for AN 010